Hello there,
I have made DFF layout in ON semi 0.5um (previous AMI 0.5um) process. The DRC is clean. Now, I am having an issue with LVS in Calibre. (For LVS, I have created netlist from Cadence and input it to Calibre. So, LVS is doing comparison between created netlist and imported gds file.)
In layout, I have used sharing source/drain technique. Now, LVS doesn't recognize the shared drain/source net and it makes the mos transistors (with shared drain/source) into a bundle object (_invv,_sup2v,_sdw2v). So, the schematic configuration can not match with layout. Is there any setting, I should try, to prevent this?
Moreover, from schematic, calibre takes a global pin "sub!". Although, I have tapped the nwell and pwell in layout for substrate, it seems that LVS cant find any "sub!" for the series mosfets (it only finds sub! connection for the pmos/nmos connected to vdd/gnd). I have gone through the LVS rule file and tried to change some of the parameters, but couldn't figure it out yet.
For your reference, I have attached the LVS summary with rule file including some comments. Can you please check and suggest me what I should do? Thank you very much!
o LVS Setup:
// LVS COMPONENT TYPE PROPERTY
// LVS COMPONENT SUBTYPE PROPERTY
// LVS PIN NAME PROPERTY
LVS POWER NAME "LVCC" "LVDD" "AVDD" "VCC" "VDD" "PS" "vdd!"
LVS GROUND NAME "LVSS" "AVSS" "ASUB" "SUB" "VSS" "GND" "NS" "gnd!"
LVS CELL SUPPLY NO
LVS RECOGNIZE GATES NONE
LVS IGNORE PORTS NO
LVS CHECK PORT NAMES YES
LVS IGNORE TRIVIAL NAMED PORTS NO
LVS BUILTIN DEVICE PIN SWAP YES
LVS ALL CAPACITOR PINS SWAPPABLE NO
LVS DISCARD PINS BY DEVICE NO
LVS SOFT SUBSTRATE PINS NO
LVS INJECT LOGIC YES
LVS EXPAND UNBALANCED CELLS YES
LVS FLATTEN INSIDE CELL NO
LVS EXPAND SEED PROMOTIONS NO
LVS PRESERVE PARAMETERIZED CELLS NO
LVS GLOBALS ARE PORTS YES
LVS REVERSE WL NO
LVS SPICE PREFER PINS YES
LVS SPICE SLASH IS SPACE YES
LVS SPICE ALLOW FLOATING PINS YES
// LVS SPICE ALLOW INLINE PARAMETERS
LVS SPICE ALLOW UNQUOTED STRINGS YES
LVS SPICE CONDITIONAL LDD NO
LVS SPICE CULL PRIMITIVE SUBCIRCUITS NO
LVS SPICE IMPLIED MOS AREA NO
// LVS SPICE MULTIPLIER NAME
LVS SPICE OVERRIDE GLOBALS NO
LVS SPICE REDEFINE PARAM NO
LVS SPICE REPLICATE DEVICES YES
LVS SPICE SCALE X PARAMETERS NO
LVS SPICE STRICT WL NO
// LVS SPICE OPTION
LVS STRICT SUBTYPES YES
LVS EXACT SUBTYPES NO
LAYOUT CASE YES
SOURCE CASE YES
LVS COMPARE CASE NAMES TYPES SUBTYPES VALUES
LVS DOWNCASE DEVICE NO
LVS REPORT MAXIMUM ALL
LVS PROPERTY RESOLUTION MAXIMUM 32
// LVS SIGNATURE MAXIMUM
// LVS FILTER UNUSED OPTION
LVS REPORT OPTION B C D F P S V
LVS REPORT UNITS YES
// LVS NON USER NAME PORT
// LVS NON USER NAME NET
// LVS NON USER NAME INSTANCE
// LVS IGNORE DEVICE PIN
// Reduction
LVS REDUCE SERIES MOS NO
LVS REDUCE PARALLEL MOS YES
LVS REDUCE SEMI SERIES MOS NO
LVS REDUCE SPLIT GATES YES
LVS REDUCE PARALLEL BIPOLAR YES
LVS REDUCE SERIES CAPACITORS NO
LVS REDUCE PARALLEL CAPACITORS YES
LVS REDUCE SERIES RESISTORS YES
LVS REDUCE PARALLEL RESISTORS YES
LVS REDUCE PARALLEL DIODES YES
LVS REDUCE C PARALLEL
LVS REDUCE C(anmv) PARALLEL
LVS REDUCE C(apmv) PARALLEL
LVS REDUCE C(pipcnm) PARALLEL
LVS REDUCE C(pipcpm) PARALLEL
LVS REDUCE schd PARALLEL NO
LVS REDUCE schd SERIES PLUS MINUS NO
LVS REDUCE enmesq PARALLEL NO
LVS REDUCE enmesq SERIES S D NO
LVS REDUCE thru PARALLEL
LVS REDUCE thru SERIES TERM1 TERM2
LVS REDUCE probe PARALLEL
LVS REDUCE ext PARALLEL
LVS REDUCE v5 PARALLEL
LVS REDUCE v12 PARALLEL
LVS REDUCE v20 PARALLEL
LVS REDUCE v40 PARALLEL
LVS REDUCTION PRIORITY PARALLEL
LVS SHORT EQUIVALENT NODES NO
// Filter
LVS FILTER C(fillcap) OPEN
LVS FILTER C(amisParasiticCap) OPEN
LVS FILTER R(amisParasiticRes) SHORT
LVS FILTER L(amisParasiticInd) SHORT
LVS FILTER D(ppnwd) OPEN
LVS FILTER D(nppwd) OPEN
LVS FILTER D(nwpsubd) OPEN
// Trace Property
TRACE PROPERTY ldd l l 0.1
TRACE PROPERTY ldd w w 0.1
TRACE PROPERTY lddn l l 0.1
TRACE PROPERTY lddn w w 0.1
TRACE PROPERTY lddp l l 0.1
TRACE PROPERTY lddp w w 0.1
TRACE PROPERTY m l l 0.1
TRACE PROPERTY m w w 0.1
TRACE PROPERTY mn l l 0.1
TRACE PROPERTY mn w w 0.1
TRACE PROPERTY mp l l 0.1
TRACE PROPERTY mp w w 0.1
TRACE PROPERTY q a a 0.1
TRACE PROPERTY c a area 0.1
TRACE PROPERTY c p peri 0.1
TRACE PROPERTY d a a 0.1
TRACE PROPERTY d p peri 0.1
TRACE PROPERTY r l l 0.1
TRACE PROPERTY r w w 0.1
TRACE PROPERTY c(anmv) l l 0.1
TRACE PROPERTY c(anmv) w w 0.1
TRACE PROPERTY c(apmv) l l 0.1
TRACE PROPERTY c(apmv) w w 0.1
TRACE PROPERTY c(pipcnm) l l 0.1
TRACE PROPERTY c(pipcnm) w w 0.1
TRACE PROPERTY c(pipcpm) l l 0.1
TRACE PROPERTY c(pipcpm) w w 0.1
CELL COMPARISON RESULTS ( TOP LEVEL )
# # #####################
# # # #
# # INCORRECT #
# # # #
# # #####################
Error: Different numbers of nets (see below).
Error: Different numbers of instances (see below).
Error: Connectivity errors.
LAYOUT CELL NAME: DFF
SOURCE CELL NAME: dff
--------------------------------------------------------------------------------------------------------------
INITIAL NUMBERS OF OBJECTS
--------------------------
Layout Source Component Type
------ ------ --------------
Ports: 6 6
Nets: 17 18 *
Instances: 0 22 * ME (4 pins)
11 0 * MN (4 pins)
11 0 * MP (4 pins)
------ ------
Total Inst: 22 22
NUMBERS OF OBJECTS AFTER TRANSFORMATION
---------------------------------------
Layout Source Component Type
------ ------ --------------
Ports: 6 6
Nets: 9 18 *
Instances: 0 22 * ME (4 pins)
3 0 * _invv (4 pins) //each bundle
4 0 * _sdw2v (4 pins) //has two mos
4 0 * _sup2v (4 pins)//(3+4+4)*2 =22
------ ------
Total Inst: 11 22
**************************************************************************************************************
UNMATCHED OBJECTS
LAYOUT SOURCE
**************************************************************************************************************
** unmatched port ** sub! on net: sub!
