Clik here to view.
correct settings for a design with an e.MMC component?
I would like to route an e.mmc-component. In this case, there is the special request that unused pins of the component are used for routing. That means, all unused pins of the component are defined "no...
View Articlecustomize style set
how to customize the style set?how to show the properties of the component in layout near by those components using style set?whether it is done through plugin impoting or it can be done mannually?if...
View ArticleExisiting Project is not visible
In 2015.1 SP1606Step 1.When I search existing project_1 in Capital project, its invisible Step 2. To cross check its real existence ,When I list existing project_1 using List Projects Web service, it...
View ArticleClik here to view.
Is there any way to easily program your F keys for Xpedition?
F4 is blank and it would be nice to have it set to Toggle Gloss. =)
View Articlein VX1.1 howcan i place components directfrom dxd to pcb in cross prob
after annotating the design i startplacing but i didnt maneged to place direct from the dxd
View ArticleChange Route Obstruct type
I'm developing an automation in PCB env.That import a mechanical frame and I've some problems I hope you could help solve.I need to change the type of "Route obstruct" to "Draw object" .According to...
View ArticleVPL dimensions mismatch
Hello I have an issue while measuring the VPL package through the VLM Software (Valor -VLM) ...The measuring dimensions are different from the given value ,I have attached the evidence...Please share...
View ArticleIntegrator-to-XC Sync Issue
Good morning, I’m running into an issue when I sync wire information froman Integrator plane to a harness in XC where some wires “lose” one connectionpoint. So then, after running design rule checks I...
View ArticleLP wizard export to central library
Hi colleagues,Is there a possibility to export decal created in LP wizard to PADS central library? It is possible to export decal and to PADS libraries (pd9,pt9) which can be automatically added to...
View ArticleDRC rule to check Density of a circle
Hi, How would you write a Calibre DRC rule that checks the density of a circle? I've tried the following: CUP.14_M1 { @ Minimum density of Metal1 area under copper pillar >= 50% DENSITY Metal1...
View ArticleSome warnings in DDRx Batch Simulation
Hi, After I set the ibis model and run the DDRx batch simulation, some warnings are reported in the audit, the audit seems unable to accept my differential pair settings.Part of the DDR_log files is as...
View ArticleDDR4 model selection while simulating ADDRESS signal
As there is fly-by topology used in DDR4 address, command and control signals. I am doing address line signal integrity, as address line have I/O logic as SSTL12. But in ibis model it comes as three...
View ArticleIs there a edit mode to Auto-Route?
The Auto-Route is very good but when we talk about ground nets/wires! Why Auto Route leaves ground conductors so short? Is there a way to edit or increase this length from ground conductors in autoroute?
View ArticleDifferential pair to multiple in pad router
Dears,could any one help me in pads router I cant rout a Differential pair to multiple points in pad routerthanks
View ArticleODB++ output, how to avoid warning message for invalid part number
I'm using VX.1.2, update 5. As soon as I select 'Output - ODB++' I get a message WARNING: This design contains data not compatible with the ODB++ file format. Please review the errors reported in the...
View ArticleNecessity of 2W between Differential pairs ?
Hello All , We have came across a stackup where we are not getting 2W spacing between differential pairs . Trace width for maintaining 100 ohm is 5.5mil and spacing between differential pairs is 7mil ....
View ArticleHow to make a grouped BOM
Is it possible to make a grouped BOM from Part Lister in DX Designer? I assume it would be possible to group the BOM on for example Product Number but how do I set up Part Lister for that? BR,Johan
View ArticleClik here to view.
Layer Stackup
Is there a way that I can get Expedition to display the layer stackup so that I can use that in a fab drawing. I pasted below the type of layer stackup that I would like Expedition to display.
View ArticleDecal editor can't remove padstack layers
Hi, I have just loaded Pads layout VX1.2.New enhancements to the padstack editor using Setup > padstacks works OK.When selecting a padstack and right click padstack I can't delete any added...
View ArticleClik here to view.
Missing configuration files
When I load L-Edit I get the following warning:"The Workgroup and User configuration files do not exist. Workgroup: C:\MentorGraphics\Tanner EDA\Tanner Tools v2016.1\x64\ledit.ini User:...
View Article