Import Decal into Dxdesigner
Hello, EveryoneI am moving from netlist based design to integrated design in xDdxdesigner. I wonder if anyone knows how to import PCB decals into Central Library. I was using Pads Layout before. It has...
View ArticleDRC rule to check Density of a circle
Hi, How would you write a Calibre DRC rule that checks the density of a circle? I've tried the following: CUP.14_M1 { @ Minimum density of Metal1 area under copper pillar >= 50% DENSITY Metal1...
View ArticleClik here to view.
new license files.
Is there anyone out there that can walk me through installing new licenses since mine expired I have the new license files.The videos do not work for my PADS .
View ArticleClik here to view.
ERROR: The Common DataBase cannot be locked for writing: Object already...
Hi i created a new project but when i try to package it in give me that ERROR:ERROR: The Common DataBase cannot be locked for writing:Object already locked (While trying to lock object)!THE iCDB WILL...
View ArticleVX1.2_User_defined_layers in Library Manager
Hello all,can somebody help me with one issue in Library Manager? I defined a user layer in Library Manager (Setup\Setup Parameters\General\Layers) and I expect I'll see this new layer in a new design...
View Articlereplacing part in dxd to other part from data book with no change to refdes
i need to replace 200 caps that came from databook with other cap value that defined in databookwhat i find is a way to change symbol but not replacing all the partpls. help
View ArticleCapital Integrator - Network termination in same connector
I need the auto-route works with a network configuration that I have a little detail, the beggining and ending are in same connector. I already change termination pins to "IxO_Terminated" and...
View ArticleCapital launcher question
In vesys I was able to open just one the schematic program and it would check out a harness license as well so i could work in both the schem and harness in one window. How am i able to do this in...
View ArticleDid Mentor Fix the "Remove unused pads" for High-Speed Signals?
When routing high-speed signals via pads in the board stack-up create parasitic capacitance. Much of the literature recommends removing unused pads except where necessary for routing. I thought I...
View ArticleClik here to view.
How to deal with Connector's extra index no.
Hello All,In the above daigram there are 11 cavities,and wire no.are also 11 ,but there are 15 index number.how to avoid 4 index which has - in place of wireif anyone know how to avoid this...
View ArticleDDR4 model selection while simulating ADDRESS signal
As there is fly-by topology used in DDR4 address, command and control signals. I am doing address line signal integrity, as address line have I/O logic as SSTL12. But in ibis model it comes as three...
View ArticleCapital Integrator - HDSI file - Not Contain Terminals
Hi, In topology (integrator), my HDSI in Bridge out command is not been builded with Terminals Part-numbers. What is necessary to make integrator to process Terminal part-numbers?
View ArticleClik here to view.
How to Convert DxDesigner schematics from PADS 2007 to PADS vx1.2?
I have old schematics designed using DxDesigner PADS v2007. I am trying to open them in DxDesigner PADS vx1.2 however when I try to open them, it opens up as a notepad file rather than a schematic...
View ArticleMentor Graphics license manger fails to start.
Since patching my Solaris 10 server the Mentor Graphics license manager fails to start. I am getting the following error: MRI damon initialization error: FlexLM platform not enabled.
View ArticleIntegrator - Wire - Attribute - Terminal Material Code - Automatic Selection
Hi, How can I do to make automatic the wire atribute "terminal Material Code" ? I already putted terminal material in capital logic in each pin from each device in "Contact material" attribute:Capital...
View ArticleDxDesigner Verify/DRC Scripts
Does anyone have any scripts that perform custom DRC checks on a DxDesigner schematic that they would be willing to share?
View ArticleIncluding Internal Component-Pin Delay in CES
Hello All,How to include internal component pin delay in the CES? Also, I'm facing issues in creating EBD pin pairs. Let me know any ways to include pin length to the device pins in the CES - Arunraj
View ArticleDatabase for DxDatabook
We use DxDatabook to manage the parametric database of our parts. Originally we started out with excel to drive odbc, then we moved to mysql and wrote a custom front end to the database for creating...
View ArticleLogical - Reducing Option Expression with Combination - where is it used?
I have a big option expression described below:(( EN_AP || EN_B4 || EN_BI || EN_XZ || EN_Y2 || EN_YD ) && TR_W7)This big expression could be described like DRGAT, I used a Combination to try to...
View ArticleVX1.2 - Script - CellEditorGRAPHICS - Adding "Property_Text" in BATCH
Hello all,help me please.I need add to all my cells a new Property_Text property in batch by a script. (The result is on the picture - made manually).It is not possible to do by ALE.I didn't find a...
View Article